High-end safety gloves manufacturer and supplier in China.Welcome your inquiry!
open list
HOME home News news Production and storage of cut resistant gloves

Production and storage of cut resistant gloves

2022-07-11

Production and storage of cut resistant gloves

 

The most common cut resistance standard is the UK EU BS EN 388 (equivalent to the Australian/New Zealand standard AS/NZS 2161.3). The specification covers 4 types of mechanical risks, namely anti-wear, anti-cut, anti-tear and anti-stab. Gloves that meet the specifications must be marked with the shield logo of the blacksmith's hammer and iron image, and express the degree of protection on a scale of 1 to 4, with a cut resistance rating of up to 5. Sometimes "x" and "0" are also used, indicating not applicable and a rating lower than "1", respectively. Gloves must also meet the general, comfort and efficiency, test procedures and labelling and information requirements set out in BS EN 420, such as water penetration, release of hexavalent chromium from leather gloves, etc.

When conducting the cut resistant test, take a sample from the palm of the glove, cross-cut it back and forth with a tungsten steel rotary cutter, and record the number of revolutions required to cut through the sample to compare the results of the standard cotton sample that was cross-tested at the same time. The higher the index, the stronger the cut resistance. However, the cut resistance test is not suitable for very hard materials.

 

Cleaning and storage of wire gloves

 

1. Wash gloves with soapy water (50°C) or hot water (50°C) mixed with detergent, at least once a day.

 

2. Washed gloves should be stored in a cool and ventilated place.

 

3. Do not clean the wire gloves by hitting them with hard objects.

 

4. Avoid contact with sharp objects on the surface of the gloves as much as possible during use.

  Precautions

 

Cut-resistant gloves should not be used when repairing thorny plants. Because cut-resistant gloves are made of steel wires, there will be many dense small holes to allow thorns to pass through. Correct gloves should be used when repairing flowers and plants to avoid injury.

 

Cut-resistant gloves are designed for people's long-term industrial safety. Under long-term use, small holes may appear in the gloves after continuous contact with sharp knives. If the small holes in the gloves exceed 1 square centimeter, the gloves need to be repaired or replaced.

 

About Us

 

Qingdao Handdier Safety Co., Ltd. was founded in 2008. As the leading manufacturer and exporter of safety gloves in the world, we always commit to R&D, produce and sales of comfortable gloves, breathable gloves, wear-resistant gloves, cut-resistant gloves, cold-proof gloves, heat-insulating gloves, waterproof gloves, oil-proof gloves and other functional gloves in multiple applications.

 

Cut Resistant Gloves, Heavy Duty Gloves, Impact Resistant GlovesInsulating Gloves ,Latex Coated Gloves, Leather Gloves, Mechanic Gloves, Nitrile Coated Gloves, Pu Coated Gloves, Water Proof Gloves, Other Gloves

 

Click the link below to view our premium products.

 

1. Cut resistant, PU palm coated gloves

2. 13G anti-cut, sandy nitrile coated gloves

3. Anti-cut double nitrile half coated gloves

4. Double nitrile anti-cut coated gloves

Products View All

Qingdao Factory Address: Majia Village, Jiaoxi Town, Jiaozhou City, Qingdao, China

Nantong Factory Address: Caobu Town, Rudong County, Nantong City, Jiangsu Province, China

Mail : korrina@handdier-safety.com korrinaliu@gmail.com Tel / Whatsapp / Wechat : 86 18554852156
Looking forward to your inquiry
Your email
Find us on

Contact

wdh-site
Thank You!

Your information has been sent to us, we will reply you shortly

OK
wdh-site
Bad!

No success, please try again!

Try Again